ZEKOO 4-10 FT Antique Style Black Steel Sliding Barn Door Hardware Roller Track Kit from US

Take 4 FT Single Barn Door Hardware For Example (doors not include)

Package List

1 x 4FT Rail

2 x Steel Hanger with bolt

4 x Door Stopper with Hex Wrench

3 x 1-3/8'' Spacer with lag bolt

2 x Anti-Jumper with screw

1 x Floor Guide with screw

1 x Single Barn Door Hardware Installation Manual

The barn door hanger roller with Professional bearings, make your barn door hardware service life last longer

About the bearing

• Material quality is high purity bearing steel Gcr15, professional bearing materials, ring fixed structure bearing, wraps around the steel ball and prevent steel ball from leaving the locus, make sliding more stable.
• There is a dust cover the bearing to prevent dust from entering and lubricating oil leakage, letthe roller can slide smoothly and more durable.
• 1 hanger with 2 life time lubricated bearing, ensure sliding balance and stability, test beyond 160,000, you can use it for a long time.

About the hanger

• The roller surface is covered with nylon, wear-resisting and slide very quietly.
• We design the Dowel pin Front part slightly larger, keep the dowel stuck in hole not fall off.
• All of prat is make by Q235 carbon steel, thick is 1/4'' (6.3mm)
• 8 grade roller bolt can hold the doors comfortably
  

About 4 FT Single Barn Door hardware

• Track: 1 piece whole 4ft rail, Pre-drilled 16" apart holes on track, make by solid 1/4" thick steel, with 8.8 grade high strengh bearing capacity lag blots, fit for concrete wall and wooden wall

• Track spacer: Provide 1-3/8'' length spacer, fit for door thickness less than 1-3/4", If your door thickness is greater than 1-3/4‘’, we also have more longer spacer for you to choose from or you can add a headboard on wall, then install the track
  

• Door stopper: Prevent the door falling off from the track, one door have 2 stoppers, ensure the stability and safety, with the rubber plug, good damping effect and reduce the noise, have 2 screws to fasten stopper on track, you can put stopper on track where you want to stop your door, easy to remove if you want adjust

• Floor guide: can prevent the door swinging back and forth or against the baseboard, let your door slide on same locus, fit for all thickness with grooved or ungrooved doors

• Anti-jumper: can prevent door to be lifted off rail when the barn door slide, ensure the stability and safety

Single barn door instruction step by step with fractional measurements in inch, have detailed word instructions with pictures

Installation Notice

1. The track drilling hole on wall is = your door height + 1-11/16''

2. We suggest 1-3/8" ~ 1-3/4" thick door, if you use for other thick door, please tell us, we will provide some accessories to you; And each track limited 230lbs.

3. Only 6" from top of door to ceiling space is required for the double barn door hardware system to install.

4. This is double barn door kit, the gap between door&wall is about 5/8'' , the gap between two door panels is about 5/8'' based on door thickness 1-9/16''

5. The hanger first hole install on door is 1-9/16” from top of door, second hole is 3-9/16” from first hole

Q&A

Q: How to choose barn door track size?

A: Barn door track length should be twice of total door width. For example, if you each barn doors is 24'' wide, you will need 2*24'' = 48'' （4FT） long track, your opening will show fully, you can use the track which is a little bit longer and please let your door a little bigger than the opening.

Q: What accessories is required if I want to install more doors?

A: You can buy an extra set of hangers, we have the hanger sale on shop.

Q: Can i cut the track?

A: Yes, you can cut it into any length of you want

Other information