ZEKOO 5-12ft Bypass Sliding Barn Door Hardware Kit, Single Track, Double Wooden Doors Use, Flat Track Roller, One-Piece Rail, Low Ceiling
Single Sliding Barn Door Hardware kit
ZEKOO provides 5 years warranty on all components, ensure you will get everything you need in a timely manner. If you have missed or broken parts, we will ship free replacement at first time from U.S warehouse. If you have any problem in using it, our professional staff in the barn door hardware field will answer you questions in 24 hours.Take 5 FT Single Track Barn Door Bypass Hardware For Example (doors not include)
Package List
1 x 5FT Rail
2 x Straight Steel Hanger with bolt
2 x Offset Steel Hanger with bolt
4 x Door Stopper with Hex Wrench
4 x 1-3/8'' Spacer with lag bolt
2 x Anti-Jumper with screw
2 x Offset Anti-Jumper with screw
2 x Floor Guide with screw
1 x Barn Door Hardware Installation Manual
The barn door hanger roller with Professional bearings, make your barn door hardware service life last longer
About the bearing
- Material quality is high purity bearing steel Gcr15, professional bearing materials, ring fixed structure bearing, wraps around the steel ball and prevent steel ball from leaving the locus, make sliding more stable.
- There is a dust cover the bearing to prevent dust from entering and lubricating oil leakage, letthe roller can slide smoothly and more durable.
- 1 hanger with 2 life time lubricated bearing, ensure sliding balance and stability, test beyond 160,000, you can use it for a long time.
About the hanger
- The roller surface is covered with nylon, wear-resisting and slide very quietly.
- We design the Dowel pin Front part slightly larger, keep the dowel stuck in hole not fall off.
- All of prat is make by Q235 carbon steel, thick is 1/4'' (6.3mm)
-
8 grade roller bolt can hold the doors comfortably
About 5 FT Single Track Barn Door Bypass hardware
-
Track: 1 piece whole 5ft rail, Pre-drilled 16" apart holes on track, make by solid 1/4" thick steel, with 8.8 grade high strengh bearing capacity lag blots, fit for concrete wall and wooden wall
-
Track spacer: Provide 1-3/8'' length spacer, it can control the gap between the door and the wall. If you have the door trim on wall, you can change other length spacer, please tell us.
-
Door stopper: Prevent the door falling off from the track, it installed at the end of the track 2 side, ensure the stability and safety, with the rubber plug, good damping effect and reduce the noise, have 2 screws to fasten stopper on track, you can put stopper on track where you want to stop your door, easy to remove if you want adjust
-
Floor guide: can prevent the door swinging back and forth or against the baseboard, let your door slide on same locus, fit for all thickness with grooved or ungrooved doors
-
Anti-jumper: can prevent door to be lifted off rail when the barn door slide, ensure the stability and safety
Single track barn door bypass instruction step by step with fractional measurements in inch, have detailed word instructions with pictures
Installation Notice
1. The track drilling hole on wall is = your door height + 1-11/16''
2. We suggest door thickness less than or equal to 1-9/16", if your door thickness is 1-9/16", the gap between inner door&wall is about 5/8" , the gap between two door panels is about 1-3/16'', the outer door extend from the wall is 5''.
3. Only 6" from top of door to ceiling space is required for the double barn door hardware system to install.
4. The hanger first hole install on door is 1-9/16” from top of door, second hole is 3-9/16” from first hole
Q&A
Q: How to choose barn door track size?
A: Barn door track length = Your opening width + 1FT. For example, if your opening is 4FT(48'')wide, you will need 4FT + 1FT = 5FT(60'')long track, your each door needs to be 30'' wide, your opening will show 25'' wide when the door open.
Q: Can the single track bypass barn door hardware system let the opening show fully?
A: Yes, you can select a longer track, if each door is 30'' wide, you can choose 7.5FT track kit.
Q: How confirm door width for the single track bypass system?
A: Because this is single track bypass, one track hang 2 doors, the wheel diameter is 2-5/8'' , so there are at least have 6'' overlap between 2 doors when your install the hanger close to the edge of door, usually it will have 8''-10'' overlap, so your each door width = Half width of opening + 5'' to 6''
A: No, the 2 doors slide on same track, so the 2 rollers will be hit together when one door slide to the end, maybe drive another door slide, if you have enough ceiling space above door for 9'', you can choice double track bypass system, please search ASIN number B06XPYZV8M from our shop
Q: Can the single track bypass use for four door also?
A: Yes, you can add 1 set straight hanger B01KH3OH62 and 1 set offset hanger B08L4FN1ZP for the other 2 doors, please search the product number from our shop, just need to know that there have 8''-10'' overlap between 2 doors, so each door need 5''-6'' wider
Q: Can i cut the track?
A: Yes, you can cut it into any length of you want
Other information
Material |
1/4 inch(6.3mm)High Standard Q235 Carbon Steel |
Finish |
Powder Coated |
Packing |
1 box/carton |
Mouted |
Wall Mouted |
Serviceable Range |
Villa, home, office, apartment, public facilities, other buildings |